How to install high-speed Internet in a private home. Internet in a private house

Meter wallpaper remains a curiosity for most domestic users, although they differ from ordinary roll products only in their width of 1 meter. Thanks to this feature finishing work take less time and effort, but the task becomes more difficult if you have to work alone. In this case, it is important to know how to glue meter-long wallpaper for one person.

If we talk about positive aspects this material, the following stand out in particular:

1. A small number of joints. To finish one room you will need half as many strips, so you will have to worry less about the correctness of the joints. It also gives the impression of a monolithic coating.
2. Speed ​​of work. Wide fragments cover a large area; it is easy to calculate that it is easier to glue three strips than six.

But there are also some disadvantages:

• The material requires a perfectly prepared base.
• High consumption. Wide wallpapers are more expensive, so if a small strip is not enough, you will have to pay for a whole additional roll.

Note! Typically, wide wallpaper is applied by two or three people, but you can do it yourself if you work quickly.

If a person has already had to glue ordinary half-meter wallpaper, then he can cope with meter-long canvases

Preparatory work

Before gluing wide wallpaper, you need to carry out a number of procedures, which include preparing tools and surfaces, as well as calculating required quantity material.

How to calculate wallpaper footage

Correctly carried out calculations will save money and also save you from making a second trip to the store or ordering additional material at home. The first step is to calculate the perimeter of the room. To do this, you need to measure the length of adjacent surfaces and multiply the result by 2. Let's say one wall is 3 m long and the other 4 m. This means that the perimeter of the room is 14 m. Since we are talking about meter-long wallpaper, it will take 14 strips to cover the wall.

Now you need to find the largest distance from the floor to the ceiling and multiply it by 14. For example, the height is 2.5 m, multiply by 14, it turns out 35 meters. This is the minimum amount of material. If the room has windows, doors, a balcony, etc., it is better not to subtract their dimensions during calculations, this way there will be a supply of material left.

Some people think that it is not necessary to tape off the area behind the furniture, since the wallpaper will not be visible there. Here the decision is only up to the home owner, but it is important to remember that when rearranging, bald spots will appear on the wall. A bulky cabinet that won’t move until it’s renovated doesn’t need to be covered with paper.

When calculating the amount of material, it is recommended to take into account 1-2 rolls of stock. They may be required not only during pasting, but also after. If there are children or animals in the house, then damage to the wallpaper is a matter of time. So that later you don’t have to look for the same ones to replace the area or completely re-glue, it is better to immediately purchase a supply.

Surface preparation

When gluing meter-long wallpaper, the most difficult stage is the preparatory stage, as is the case with any other types of these products. If the apartment goes major renovation or finishing after putting the object into operation, then all of the following measures must be carried out during work on the ceiling. So, you need to do the following:

Wallpapering should only be done on clean and well-primed walls.

1. Remove the front panels from all sockets and switches and carefully seal the resulting holes.
2. Remove all fasteners from the walls: screws, nails, dowels, and so on.
3. If there is coating on the walls, you need to remove it. As a result, not even a small fragment of finishing material should remain.
4. Check if the walls are level. To do this, apply a building level to them at different points.
5. For minor distortions, it is enough to use finishing putty; for serious distortions, plastering may be required.
6. Wait for the material to dry and sand the area.
7. Before gluing wallpaper on the walls, it is necessary to treat the coating with a primer. This material will increase adhesion and save on glue. The drying time for the compositions varies, but usually it is several hours.

Required Tools

To carry out the work you will need:

• wide brush, roller or brush for applying glue;
• container and construction mixer for preparing the composition;
• ruler, level, stationery knife, marker or pencil;
• rubber spatula and roller for ironing wallpaper;
• a rag to remove glue residue.

To paste walls with wide canvases, a generally accepted wallpaper tool is used.

Pasting

Step-by-step instructions on how to glue wallpaper alone:

1. Prepare the adhesive according to the instructions on the package.
2. Use a level and a pencil to mark the top border.
3. Fold a small part of the strip to form a corner.
4. Place the material against the wall and press firmly.
5. Iron the glued wallpaper with a rubber spatula, moving from the center to the edges. You can also use a roller to get the air out.
6. Using a metal spatula and a utility knife, trim off the excess.
7. Inspect the strip and make sure it is completely stuck to the base.

Damp wallpaper is difficult to cut, so in some cases you will have to wait.

Regardless of the width of the canvas, the room is covered according to the same pattern

Docking

The glued sheet must be butted against the adjacent one. If there are patterns on the wallpaper, then it is important to adjust their height. During gluing, the strip must be smoothed at the same time and ensure that it does not move away from the previous one. In this case, it is forbidden to stretch the material to achieve joining; after drying, it will shrink back and there will be a gap.

The joints are rolled with a special roller; an attempt to forcefully pull the sheets together at the seam will lead to the appearance of a gap after drying

Note! If you need to glue non-woven wallpaper, you can move it along the surface for 10 minutes after pasting. If you use another type of wallpaper, then you should choose an adhesive without additives that accelerate drying.

If the joint does not work, you can overlap the wallpaper and then cut off the excess using a utility knife. The remaining unglued side should be coated with glue and ironed with a rubber roller.

Wallpaper joining with overlap and trimming

Pasting in hard-to-reach places

Now let’s talk about how to hang wallpaper for one person in the corners, behind the radiator, above the doorway. It is better to arrange them at the main stage of pasting. To do this, leave a small overlap (about 2 cm), which will overlap the adjacent wall. To hang wallpaper behind and under the radiator, you need to cut the material into small pieces and select a pattern. After this, the pieces are glued to the wall, as described above.

A simple way to cover the wall behind a radiator

Another difficulty that you will have to face is covering the area with sockets. If at the preliminary stage the front panel was removed and the voltage was turned off, then you just need to glue the strip, not paying attention to the hole, and then use a knife to cut through the wallpaper. If you get uneven edges, that’s okay, the front panel will hide these imperfections. In the case of door jambs, it is necessary to glue the sheet with a margin of 5 mm. After smoothing, the excess length is trimmed or covered with a casing.

It is advisable to cut holes for sockets and switches after the canvas has dried

Before working with meter-long wallpaper alone, it is recommended that you familiarize yourself with some expert advice:

1. There should be no drafts in the room, a suitable temperature range is from +5 to +25 C. In addition, it is also quite difficult to work in damp rooms, so at the preparatory stage it is necessary to ventilate and carefully close the room.
2. If gluing is planned in the cold season, then it is better to turn off the radiator. If it is not possible to do this, it is recommended to reschedule the work while the central heating is turned off.
3. Most adhesives are universal, but when choosing, it is better to ask the seller what type of products this composition is suitable for. This will help fix the wallpaper on the surface better.
4. If immediately after pasting, defects are noticed, in particular uneven joints, it is necessary to lift the canvas with a spatula and correct the problem. It is very important not to pull the stripes.
5. After gluing, sometimes difficulties arise with cutting the material. To do this, use a stationery knife or scissors. You need to press the excess part with a spatula and run a knife along the markings. In the case of scissors, you need to bend the edge along the markings and cut it off.
6. If there are uneven cuts at the top or bottom of the wall, you should not try to fix it. As practice shows, this will lead to bad consequences. It is better to purchase skirting boards that will hide imperfections.

If ceiling fillets are not provided, then the perimeter can be cultivated using a frieze

Knowing how to hang wallpaper with one person, you can avoid conflicts and complete the entire amount of work in a short time.

Most often, it is two people who are engaged in wallpapering a room. One stands on a raised platform (stepladder, stool) and waits for the second to cut the required strip and spread it with glue.

Then the wallpaper is applied to the wall and combined with the previous strip. Next, one smoothes it out, removes unevenness, and the other watches the process.

Useful information:

And everything would be fine, but in most cases such work is accompanied by disputes and often ends in a quarrel. Moreover, all stages of the process can be performed alone.

Preparatory stage

First you need to prepare the following set of tools:

• ladder;
• large container for diluting glue;
• cuvette for prepared glue;
• wallpaper ruler, tape measure, pencil, level;
• brush from 50 mm wide;
• paint roller (width 250 mm);
• rubber roller for smoothing wallpaper;
• rubber roller for smoothing joints;
• sponge, napkin for cleaning surfaces from excess glue;
• pliers, screwdriver, electrical tape.

You will also need material to cover the floor. It can be cardboard or wide film. If the wallpaper is too heavy, you will need a cone-shaped roller with ribs. They smooth out the joints. When wallpaper requires particularly careful handling, the roller is replaced with a special wallpaper brush. You can purchase a plastic wallpaper spatula. It is used to form geometrically correct angles. If the wallpaper has a nasty texture, you can smooth it out with this spatula, replacing a regular roller.

How to prepare the surface?

At the preparatory stage, it is necessary to carry out a certain set of works with the surface. No matter how fashionable and attractive the wallpaper is, general view won't be perfect until finishing materials there is an uneven surface, replete with potholes and protrusions. That's why . Moreover, each layer requires a good primer. Such walls will last for many years, the wallpaper on them can be changed many times.

Of course, from the walls. If non-woven wallpaper was pasted there, it will be removed without a trace. When removing vinyl, which is the most common type, the backing will definitely come off and remain on the wall. There is nothing wrong with this; it will be the basis for new decorative finishing. If the layer of plaster and putty holds up well, then there is no need to worry about the fact that some of the vinyl wallpaper remains on the wall.

Advice! To make sure the surface is durable, you need to draw two intersecting lines with a sharp object. If only the indentations from a sharp object remain without chips at their intersection, then the surface is durable. This test should be carried out in places where the scratches will not be very noticeable later.

How to carry out pattern fitting and marking?

When pasting, the main difficulty is related to matching the pattern. Rapport is part of an element of a repeatedly repeating ornament. It is rapport that is taken into account when adjusting the pattern. The size of the repeat is related to the size of the ornament or pattern. The larger the drawing, the larger the step will be, and accordingly the amount of waste will increase.

The initial stage of work involves adjusting the pattern, marking the fragments and folding the prepared strips in the desired sequence. Photo 1 shows heavy vinyl wallpaper with large patterns.

First, roll out 2 rolls of wallpaper. You need to make sure the floor is clean. From the first roll, measure a strip to the height of the ceiling, adding 10 cm. This strip is laid out on the floor. The second one is combined with it so that the pattern of one stripe continues on the second fragment. Marks are made on the canvas as shown in photo 1.

Photo 2 shows how to make marks using scissors. The alignment of the strip in the area where there is a cut is shown in photo 3. The bend is smoothed out by hand.

Next, cut off a strip of wallpaper using scissors. How to do this is shown in photo 4. The edge will be a little uneven. There is nothing wrong with this, because an allowance of 10 cm is left. It allows for more accurate and even cutting on the spot.

The strip that was previously used for marking must be put aside, but first you need to make a mark indicating the upper part. And put a number on it. How this can be done is shown in photo 5. Then the strip is folded as shown in photo 6.

It is more convenient to place the prepared strips near the wall for which they are intended. The vertical position will help save space. See photo 7.

Do the same with the next canvas. See photos 8, 9. This method preparing the wallpaper allows you to subsequently correctly join the pattern, quickly straighten the canvases, and save space and time.

At standard way Before preparation, strips cut to size are laid flat on top of each other. Next, the upper strip is smeared with glue, while the edges of the lower ones get damaged, get dirty, and then the overall picture deteriorates.

How can you mark the surface of the walls?

Marking the walls is an important stage. Usually the instructions say that you need to use a plumb line. But today the use of a plumb line is becoming a thing of the past. Use it. In this case, both a water level and a laser level are taken. Using this tool, mark where the first stripe from the corner should go. To do this, draw vertical lines. The level determines the direction of the position of the curb, which is attached horizontally, and coordinates the joining zones.

In photo 10 you can see how to use a water level. You need to pay attention to where the bubble should be. Experts recommend that when applying markings with a pencil, make light strokes without pressing on it. A clear bright line will appear through non-woven wallpaper and ruin appearance. Even if you take a different type of wallpaper, it can also become dirty with graphite particles.

It is necessary to leave a width tolerance. If after measurements it turns out that the strip of wallpaper is 53 cm wide, you need to step back from the corner by 54 cm. In this case, the mark will be constantly visible. This way, the person who is pasting the wallpaper will be able to constantly see the landmark and will not allow any failures or distortions.

How to apply glue and stick canvases?

If the preparation was successful, you need to begin the pasting process. While work was being done on the last stripes, the first ones were already well straightened out. The glue is diluted according to the instructions on the package. Regardless of the type of glue, prepare clean cold water. The glue should be poured little by little, in a small stream. In this case, the composition must be constantly stirred.

There is no need to rush and pour 2 packs of glue into the bucket at once. The mixture will gradually begin to thicken, and the resulting lumps will interfere with your work. When choosing glue, you need to take into account the characteristics of the wallpaper. Each variety needs its own type of glue. Wide cardboard or prepared film is spread on the floor. The wallpaper is laid on it, base side up. For more convenient use, pour a small amount of glue into a cuvette, into which the roller is then dipped. The most common application method is shown in photo 11.

When applying glue, pay special attention to the edge part. Today they produce glue with an indicator. After dilution, it has a certain color shade, which allows you to know exactly where the glue has already been applied and where it has not yet been applied. If glue gets on the surface under the wallpaper, there is no need to panic. It can be easily removed later. When working, you need to make sure that the layer of glue is not too thick, and that the application itself is even.

When the glue is applied, the wallpaper is folded in half. You can see how to do this correctly in photo 12. The wallpaper should remain in this position for at least 3 minutes. This time is enough for the glue to be absorbed. You can increase the time to 5 minutes when the wallpaper is too thick. If the next section of the wall is smooth, without protrusions and various parts, you can immediately prepare the 2nd strip. But you shouldn’t get carried away with this. The number of prepared strips should not be more than 3. Otherwise they will start to dry out and stick together.

When the strip is ready, it is unrolled, gradually ascending the stepladder. You need to hold the strip by the part on which there is a mark indicating that this is the top. When applying wallpaper to the wall, you need to take into account that you need to make an overlap on top. Its size is individual, depending on the characteristics of the room.

In photo 13 you can see where the pasting and fitting begin. First they work with the upper part. When everything is ready there, they come down from the stepladder and straighten it, applying the lower part. When everything is joined, you can start working with a smoothing roller, spatula or brush. Movements come from the top, from the middle. Then they go down. How to squeeze out the air can be seen in photo 14.

When the wallpaper is smoothed and the air has been removed, you need to roll the joints with a special rubber roller. However, seams do not like too active exposure. Therefore, you should not rub them or put pressure on this area. When excess glue appears, it is carefully removed with a sponge or napkin, and they are subsequently rinsed in water.

If you do not put unnecessary pressure on the seams, they will look almost perfect after drying.

How to cover areas with sockets and switches?

All sockets, switches, and other parts that violate the geometry of the walls must be removed before wallpapering. Firstly, this will allow you to later easily change them to smaller models. Secondly, the appearance of the switch installed on top of the wallpaper is more aesthetic and modern.

Some people advise cutting the part of the wallpaper that remains under the socket or switch crosswise and then bending the paper to the sides. This is unsafe in case of fire. It is better to make a cutout that matches the shape of the device, only smaller. This can be seen in photos 16, 17.

The slots are made immediately after gluing the corresponding strip. Firstly, you can later make a mistake with the place. Secondly, after drying the wallpaper will stretch, so making cuts will be more difficult. Before removing sockets and switches, you must turn off the current, and carefully insulate all contacts and put them inside the installation box.

How to trim off excess?

Here you will need a flexible ruler; this is a plastic tool 60 cm long; a stainless steel strip is built into its body. It is flexible, so the ruler can be pressed firmly even on an uneven surface. What such a tool looks like and how to use it can be seen in photo 18.

The peculiarity of using a wallpaper knife is that after each cut you need to break off a small fragment of its blade. In this case, it will always maintain good cutting abilities. When the excess is cut off, the surface is wiped. Photo 19 shows exactly this moment.

From photo 19 you can see that despite the wet state of the wallpaper, the cut surface is smooth and does not have any lint or fibers. Such accuracy can only be achieved through the use of a flexible ruler.

How to cover the area where heating radiators are installed?

The installation location of heating radiators is considered the most difficult for the wallpapering process. To complete all the work efficiently, you will have to make every effort. In new buildings there are fewer problems; there you can find radiators that can be dismantled and, after pasting, installed in their original place. Photo 20 shows how radiators are dismantled. After its removal, wall fasteners and floor outlets equipped with American-type connections remain.

In this case, pasting will not be a big problem. However, the process of removing the battery and then installing it will take time. Before disconnecting, you need to turn off the water supply, then the return line, and drain everything that is inside the radiator. At the same time, we must not forget about pressure. It is reduced by unscrewing the shut-off screw located on the drain valve.

If the situation is such that it is impossible to remove the radiator, you will have to insert strips about 15 cm under it. If the battery is working, you need to additionally coat the surface under it with glue.

1. A stepladder is better than scaffolding and “goats”, which often damage the surface of the walls.
2. or with fiberglass, glue must be applied directly to the wall. Therefore, there is no need to cut the wallpaper into separate strips in advance.
3. A small allowance (1 - 2 cm) on the slopes will allow you to get a neat edge. You just need to wait until the wallpaper is dry, and then trim off the excess evenly.
4. Joining the panels at the corners is impractical. Most often, a transition is made from one wall to another, leaving a large allowance equal to the vertical deviation of the wall. The second canvas is glued onto the first one with an overlap, guided by the level indication. Then both sheets are cut through and the excess is removed.
5. It is better to lay the flooring after pasting the walls. The exceptions are tiles and parquet.
6. The parquet is covered with cardboard before pasting. You cannot put film on cardboard.
7. While working, you need to keep your hands clean. They are periodically wiped with a napkin, which is rinsed thoroughly from time to time.

Tweet

Stammer

Like

Many people primarily associate renovations with wallpapering. Many people mistakenly believe that there are no tricks in this matter and that it is enough to simply stick it more or less evenly and that will be enough. Warp good mood in the future - non-peeling wallpaper. To prevent this from happening, it is necessary to prepare the walls for gluing.

Preparing the wall for pasting

How to remove old wallpaper from walls?

Wallpapering old wallpaper is the most big mistake, which can be tolerated during the repair process. If for some reason you pasted new wallpaper on old ones, then be prepared that soon this entire structure will soon collapse. Therefore, first of all, you need to remove the old wallpaper. Wallpaper labels usually indicate a method for easy removal, but if the label is not preserved, then it’s okay, you can use the following methods to various types wallpaper:

— Vinyl wallpaper. To remove vinyl wallpaper, you need to make cuts on the surface and then moisten the wallpaper with water. After the water is absorbed, a horizontal cut is made at the top of the wallpaper and the wallpaper is removed in whole pieces;

— Non-woven wallpaper. In such wallpaper it is necessary to make cuts and holes, and then apply water to the surface using a sprayer. After 20 minutes, the wallpaper itself will begin to peel off from the wall;

— Washable wallpaper. This is a two-layer wallpaper, the first layer is wetted quite easily: notches are made on the wallpaper, the surface is wetted. After which the top layer comes off quite easily. It is best to remove the second layer with a steam generator; you can use a regular steam iron.

— Ordinary paper wallpaper. There are fewer problems with this wallpaper; just wet the wallpaper and after a few minutes start removing it with a spatula. In this way, you can even remove multi-layer wallpaper structures.

Wall putty

After removing the old layer of wallpaper, you need to prepare the wall. The first stage is leveling the wall using putty. High-quality wall putty takes place in three stages:

1) Covering the wall with a primer composition. This is done to improve the adhesion of the putty to the wall. It is best to apply the primer composition with a roller - this ensures uniform distribution of the primer composition over the entire surface of the wall;

2) Starting putty. After the primer has completely dried, you can begin to putty the wall; this is done to level the walls. The layer of starting putty should not exceed one and a half centimeters. If the differences in wall level are greater, then it is necessary to apply the putty in several layers; for this, a painting mesh is used; in this case, it is necessary to let the first layer of putty dry, let it dry and apply a primer solution to it.

It is worth paying attention that the packaging of the putty should indicate that this is a starting putty.

Layers of putty are applied with a spatula in small, even portions. To avoid the appearance of bumps and irregularities, it is necessary to apply the putty diagonally overlapping. To putty corners, you must use a special corner spatula. If your walls are even on their own or high-quality putty was applied during a previous renovation, then you can safely skip this stage. Starting putty is only needed to level the walls;

3) Finishing putty. After the starting putty has dried, the finishing layer of putty is applied. It removes all small cracks and irregularities, making the wall perfectly smooth. The composition used for this operation has the same name as finishing putty. The layer of finishing putty should not exceed two millimeters. If you did not level the walls with the starting putty, then the finishing putty is applied immediately to the primer after drying;

Primer of walls

The final stage of wall preparation is priming the walls. Priming the walls is a mandatory step, but many people skip it, which is not recommended. The main purpose of wall priming is to improve the adhesion of wallpaper to the wall, but in addition to this, wall priming is necessary for the following:

1. Removing dust and small debris from walls;
2. Increasing the moisture resistance of the wall;
3. Reduced glue consumption.

The priming process is quite simple and does not contain any tricks. It is best to apply the primer using a roller - this ensures an even distribution of the layer over the surface. The primer must be applied in two layers, the second layer is applied after the first has dried.

Where to start gluing wallpaper?

The first strip of wallpaper is the most important; everything will depend on how well it is pasted. The first strip must be glued strictly perpendicularly; you should not focus on the corners of the room - often they are far from the value of 90 degrees, in which case the drawing will be crooked and the result will disappoint you. You need to focus on either the window or doorway. They are always strictly perpendicular to the floor, and in this case there will be no problems with gluing. It is worth remembering that when gluing strips, you must move strictly in one direction.

Features of gluing different types of wallpaper

Paper

The technology for pasting paper wallpaper is quite simple and is divided into the following stages:

1) The roll is cut into sheets equal to the height of the wall. But it is necessary to leave a small margin of 10-15 centimeters, depending on the pattern. If the pattern is solid, then it is necessary to adjust the stripes to each other in advance. Some wallpaper has an edge on one or both sides that needs to be cut off;

2) Applying glue. The glue is applied with a brush in a thin layer. If the wallpaper is made using duplex technology, then the glue is applied in two layers. After applying the first one, the surface will become wavy. The second layer of glue smoothes the surface;

3) The process of pasting itself has no tricks. It is better to glue the wallpaper together, holding the strip on both sides. This way you can safely stick the strips strictly vertically. There is no need to rush, and the first page should be given a lot of attention, because it determines end result. When gluing corners, it is necessary to make a slight overlap;

4) The wallpaper should be smoothed with a soft cloth from the middle to the edges. This way, air bubbles will not form on the surface of the wallpaper. To smooth light-colored wallpaper, place a sheet of white paper under the fabric;

5) The glue must be removed carefully with a damp sponge. Do not forget that paper wallpaper can be easily damaged.

If there are sockets and switches on the wall, you must first turn them off, then remove the housings. The wallpaper is pasted over the rosettes, a cross-shaped cut is made with a sharp knife, then a hole is cut out.

Vinyl

Vinyl is known for its durability and the gluing technology differs from paper:

1) The roll is cut into strips according to the height of the wall. The stripes are adjusted to each other according to the pattern. Vinyl wallpapers are thick and they are glued only end-to-end. It is necessary to leave a small margin, the room may have height differences;

2) Be sure to read the instructions. Usually the adhesive is applied only to the wall, but some vinyl wallpaper requires the adhesive to be applied to a strip;

3) The sticker process is quite simple. The strip is applied to the wall, after which it is smoothed from the center to the edges with a special rubber roller; the glue can be removed with a damp sponge or cloth. Special attention it is necessary to pay attention to the joint, if necessary, glue it with a brush. When gluing the corners, you definitely need an allowance of 3-4 cm. The excess is cut off with a sharp stationery knife.

When gluing vinyl wallpaper, it is necessary that all rolls come from the same batch. Lots may vary in thickness and color tones. This will not be noticeable in rolls, but on the wall the difference will be striking.

Non-woven

Non-woven wallpaper is very specific in the gluing process; if you decide to cover your walls with this type of wallpaper, here’s what you need to know:

1) Before marking the roll and cutting it into strips, it is necessary to lay a film on the floor surface. You need to cut non-woven wallpaper with a very sharp knife. Having cut off the strip, it is rolled into a roll with the front side inward, starting from the bottom side. It is also necessary to mark the wall for each strip;

2) Glue must be applied to the wall in sufficient quantities. The strip should slide freely over the surface of the wall, but it is necessary to prevent the formation of smudges;

3) Each strip is rolled out from top to bottom, according to the applied markings. After which the strip is carefully smoothed from the center to the edges;

4) Excess glue is removed with a damp sponge, the allowances are cut off with a sharp stationery knife.

1. It is best to cut wallpaper with a kitchen knife, it is much easier to control, and cut it with a stationery knife;
2. It is much easier to trim wallpaper on window and door slopes the next day, when the wallpaper has dried;
3. It happens that the eyes get tired and the gaze becomes blurred and air bubbles can be missed. To prevent this from happening. Just run your fingers along the strip; a characteristic rustling sound will immediately reveal the location of the bubbles;
4. If a little wallpaper is missing. You can use scraps, but this is quite difficult to do with composite drawings;
5. Draft is the enemy of fresh wallpaper, so you can’t create a draft in the room immediately after pasting the walls;
6. To ensure that the glue is uniform and without lumps, it can be stirred with a drill with a mixer attachment.
7. Vinyl wallpaper on a non-woven basis is glued in the same way as non-woven wallpaper.

“How to glue wallpaper” is a question asked by almost everyone who is about to renovate. Before gluing wallpaper, you still have to go through the process of selecting it, which is quite difficult, since nowadays there is a huge selection of wall coverings. Liquids are gaining popularity fabric And non-woven materials, classic paper options still remain in trend. Moreover, each type of this coating has its own characteristics, and therefore when pasting wallpaper you need to approach each type individually.

Preparatory stage before wallpapering

Whatever wallpaper you choose, first of all, you need to prepare it for pasting the wall. The task is simplified if you need to decorate the walls in a new building. If you are doing cosmetic repairs in an apartment or house, then first you need to, if necessary, also remove the paint. To summarize: the basis of this process is the removal of unnecessary elements.

The best way would be to buy a product for removing old wallpaper (see photo).

But repairs are already a costly thing, so if there is an opportunity to save on something without losing quality, then why not do it? To make it easier to remove old coatings, you can use a regular soap solution, which is easy to prepare with your own hands.

Advice! Add a little wallpaper glue to the resulting solution. Old wallpaper will be removed more efficiently.

If the old coatings were dense, then you will have to put in a little more effort to remove them. Therefore, it is better to first cut them, and only then apply the prepared solution based on detergents. This is because the cuts improve absorption. After applying the solution, wait a little while for the old wallpaper to swell and absorb the liquid. Now you can remove them using a spatula.

Advice! If the wallpaper is so thick that it was not possible to remove it completely, then the above procedure should be repeated one more time or even several times.

However, as often happens, simply removing old wallpaper is not enough. It is also necessary to prepare the walls so that there are no unevenness, and new material lay down evenly and smoothly. Therefore, all irregularities should be plastered and puttied. Before this, it is necessary to eliminate old enamel and paint.

Condition of the walls	Proper surface preparation
New and porous walls (gypsum)	Apply a plaster primer or adhesive primer 24 hours before wallpapering (this will allow you to protect the wall and subsequently remove the wallpaper without damaging the wall surface) A primer is required if the walls are made of gypsum boards.
Painted walls	Wash the walls with a special detergent and rinse them with clean water. If the wall is painted with glossy paint, it is recommended to treat it with sandpaper in order to improve the adhesion of the glue to the surface.
Walls already covered with wallpaper	Remove old wallpaper. To do this, you can apply a special wallpaper remover to the wallpaper, which is diluted in warm water. Apply the solution to the wallpaper and let it sit for 10 minutes, then use a spatula to remove the wallpaper, starting from the top. You can also use a special steam cleaner to remove old wallpaper, except in cases where the wallpaper can be removed from the wall dry.
Damp walls	Treat the walls with a special primer for wet walls. It is necessary to observe the drying time indicated on the packaging for the primer.

The stage of immediate preparation for wallpapering

There is no need to reinvent the wheel. You just need to strictly follow the already established instructions.

• Prevent possible drafts . To do this, close the windows and doors.
• Count the number of vertical stripes that will fit on the wall .

To quickly do this, you can simply measure the length of the wall and divide the result by the width of the wallpaper. If you get a fractional number, for example, 7.7, then this means that you will need seven full strips and one incomplete, trimmed. Then cut out 8 strips corresponding to the height of the wall. Add another 50mm for trimming at the ends.

• Next you need to make markings. It is better to start wallpapering with the second strip, leaving the first unused. After all, the first page is usually near the aisles. For better orientation of gluing the first strip, you should retreat 500 mm from the edge of the wall. Mark this line with a pencil. For this you will need a building level. We apply the tool to the wall and align it with the mark. Draw a vertical line on the wall. From this place we will glue the next strip.

Advice! To do this, you can also use a simple thread and tie a weight to it.

• Let's start applying glue . They should lubricate both the wall and the strip. For this you will need a brush.

Follow these instructions and you shouldn't have any problems with gluing.

How to glue wallpaper correctly: the gluing stage

1. Let's proceed directly to pasting. Where to start gluing wallpaper? We remember that you need to start from the second stripe. She will be our first. It is better to start gluing from the top, carefully applying the coating to the wall. The edge of the strip should be aligned with the vertical line marked at the preliminary stage. You will need a wide roller to carefully adhere the covering. This will squeeze out any air bubbles.

1. Since the length of our strip exceeds the necessary one, we mark the unnecessary length . It needs to be cut off by slightly tearing the strip off the wall. It's even easier to do this using a utility knife. In this case, there will be no need to tear off the strip that is already so well glued. The resulting joint will be covered with a plinth.

1. We continue the sequence of actions described above in relation to the remaining stripes . Instead of a vertical stripe, we use the edges of the previous one.

To understand the nuances of wallpapering even better, watch the video at the end of the article.

How to glue wallpaper in corners? Photos and step-by-step instructions

Hanging wallpaper on a straight, flat wall does not cause any difficulties if the technology is followed. However, this can be challenging even for an experienced craftsman if he encounters corners. The most difficult is situation if a window is adjacent to the corner .

Here are instructions on how to glue wallpaper in the corners. Paint and other coatings should be removed from them first.

• Most important point pasting is to determine the place from where to start gluing the wallpaper . We start gluing from the ceiling to the window sill. This should be done with a small overlap on the adjacent wall.

1. Carefully process the window sill.
2. We carefully place the coating behind the battery, and if necessary, cut the strip to the pipes.
3. We roll over the strip to smooth out all the wrinkles.
4. Carefully mark a line along the corner. We cut off that unnecessary part of the strip that was overlapped onto the adjacent wall.

Advice! To do this, it is most convenient to use a ruler and a stationery knife.

1. We proceed to pasting the strip on the adjacent wall. Again we begin to work from top to bottom, joining the new strip to the one that is adjacent to the adjacent wall. Leave a small overlap unattached.
2. Cut off the unnecessary part by applying a ruler to the corner.
3. Again, take a wide roller and process the freshly glued strip.
4. Treat the space between the stripes with a smaller roller.

How to glue wallpaper on the ceiling: step by step

First of all, you should prepare the ceiling for pasting. The surface must be flat, otherwise the coating will not lie well. Therefore, the whitewash, previous coating and paint should be removed.

• Removing irregularities .

The length of the strips should be approximately 5-7 centimeters greater than the size of the plane.

• Apply glue to the ceiling with a roller .

• On the ceiling, measure the width of the wallpaper, fix this place with a line. Apply masking tape along the strip.
• With a folded sheet we climb onto the table . Peel off the corners, the sheet will open itself under the weight of its own.
• Glue the corners first, then the rest of the strip. .

Advice! Use a pin to pierce every 10-15 cm of wallpaper. Air will escape through these holes, preventing the wallpaper from coming off.

• Using a spatula, expel the air, moving from the middle .
• Roll the surface with a roller ;
• Repeat this procedure for the remaining sheets .
• Trimming the edges . Apply a putty knife and press it to the cutting area. Cut with a knife.

Based on these instructions, you can easily glue any coating.

What wallpaper is better to glue?

Nowadays, the choice of wallpaper is so large that this can become a real problem. Of course, you can focus only on aesthetic components and choose only those materials that you like best in appearance. But, perhaps, it would be much more reasonable to pay attention to the technical characteristics of the wallpaper. After all, if insurmountable difficulties arise during pasting, then you will not be interested in their beauty.

To make it easier to decide on the choice of wallpaper, let’s turn to their technical specifications, as well as the positive and negative aspects of their different types.

Currently, non-woven wallpaper is becoming increasingly popular (see photo). Largely because it is now fashionable to use only environmentally friendly materials. When gluing non-woven wallpaper, it is necessary to take into account such a nuance as gluing technology. Regarding the question of how to glue non-woven wallpaper: the glue should be applied not to the coating itself, but to the wall.

• When choosing wallpaper, you should take into account the humidity of the room and the condition of the walls. So, vinyl materials good for the bathroom or kitchen (see photo).
• This is because dirt can be removed with a damp sponge. At the same time, if you have a good budget, you can buy expensive ones. non-woven wallpaper , which can also be wiped with a damp sponge.

If you choose wall covering for the corridor, then be guided by your taste. Any type of wallpaper is suitable here; the choice is yours.

How to glue liquid wallpaper and other non-standard materials

Liquid-based coatings are of particular interest, so the question of how to glue liquid wallpaper is becoming increasingly relevant.

Prepare a container in which you will mix the coating. And follow the instructions on the package. The process resembles conventional puttying. You will learn how to glue liquid wallpaper from the video at the end of the article.

• Another popular type of non-standard wallpaper is a meter covering. Therefore, the question of how to glue meter-long wallpaper on walls is also of great interest.
• Meter-long wallpaper should be especially carefully smoothed over the wall to avoid so-called “bubbles.” This is somewhat more difficult to do than when pasting with a regular width, so you will have to try. Some types of meter-long wallpaper can be painted.
• IN lately It is becoming fashionable to apply paint to the coating. They are best suited for this. But some vinyl ones can also be painted. And, of course, you shouldn’t paint it regular paper wallpaper.

Which wallpaper is best to glue - liquid-based, paper, non-woven, meter - everyone decides for himself, taking into account the characteristics of the room. Take the above instructions as a basis - and you can easily make repairs.

IN once again, looking carefully around the room, the thought comes to you that it’s time to urgently change something. Has this ever happened? Perhaps it’s just the wallpaper that has already become an eyesore. If you feel that the answer is yes, then you need to solve the problem that has arisen - and quickly. Moreover, the process of gluing new wallpaper onto the base is within the power of anyone. In this article we will look at how to glue wallpaper at home.

What's the best way to hang wallpaper?

What is the best way to glue wallpaper? To begin with, it is better to get rid of the old wallpaper layer. It couldn't be easier to do this! For such manipulations you will need a bucket of warm (and clean!) water, an ordinary (but also clean!) rag and a scraper spatula.

This simple and uncomplicated method is used to properly prepare the wall surface for applying glue and gluing a new wallpaper covering. You can also additionally treat the wall with the adhesive composition (paying attention to its minor defects), so that the wallpaper does not lag behind and holds really tightly...

Where should you start gluing wallpaper?

The next, also very important, step towards the previously set goal is marking the wallpaper and cutting it. You need to be prepared for any surprises in advance. Please note: not all walls will be perfectly smooth, clean and straight (even after preparation and putty).

And so, where should you start gluing wallpaper in this case? You need to use a simple homemade plumb line. The initial markings are placed along the plumb line on the wall. In this case, mark the clamping point at the top; and then - the point of contact of the improvised cord plumb line at the bottom of the wall.

After this, the marked points are connected. Subsequently, during the process of gluing the very first strip of wallpaper from a wallpaper roll, one of the side edges of the wallpaper must necessarily coincide with this marking.

It is desirable that after pasting the wall you get a complete, unified pattern. Accordingly, the texture of one strip should repeat the texture (or pattern) of the next wallpaper strip.

Wallpaper strips can also be prepared in advance (or immediately before gluing them to the wall). Although this is not necessary, and not so significant.

For many people, texture doesn't matter at all. Therefore, there is no point in making too scrupulous adjustment of the following stripes an end in itself. Other people will prefer to cut the wallpaper in advance - so that they can then glue the wallpaper to fit, and in an accelerated manner. But many people cut off one strip, glue it - and then cut off the next strip...

Choose any of these options. Each method has its own. It is important that the result pleases your eyes!

If you plan to make a suspended ceiling in a room and then glue wallpaper in the same room, then a special skirting board for the ceiling will help hide the joints and irregularities between the ceiling and the wall.

If you want to simply and efficiently cover the walls, then you need to maintain a distance of 30-50 millimeters from the ceiling of the room. In the future, this distance can be easily hidden with decorating tape or a profiled smooth baguette. It will look beautiful and elegant.

In the process of gluing strips of wallpaper to the wall, do not forget to carefully monitor the surface, its evenness, as well as the possible appearance of bubbles protruding on the surface of the wallpaper. To better fix the new wallpaper on the wall, you can also use a dry, clean cloth or a roller.

With a small rag you need to make tangential movements, while with a roller you need to press the wallpaper more tightly from its middle to the edges. Under no circumstances should you rub the wallpaper with your hand! This can ruin the design of the coating (especially on wallpaper made of paper).

If the surface begins to bulge, no matter what, and don’t be afraid of this effect. Just take a needle and very carefully pierce the problematic area. Press the punctured area with a small, clean cloth to release excess air.

Don't know how to properly prepare the adhesive composition? Usually, you can buy the adhesive composition ready-made in construction hypermarkets. Just make sure that it matches your new type of wallpaper. Just don’t forget: when you mix the adhesive and water, you need to simultaneously mix the solution with a specialized stick or brush. This move will prevent the appearance of lumps in the adhesive solution.

The main types of wallpaper that can be found on the market.

In addition to the most commonly found wallpapers, such as vinyl or paper (as well as non-woven wallpaper), there are also liquid wallpapers, textile wallpapers, glass wallpapers and photo wallpapers. We will consider only the main ones.

Fabric wallpaper for walls

Fabric wallpaper for walls is endowed with increased thermal insulation and sound absorption. If flax fibers were used during their manufacture, then such wallpaper also acquires antibacterial qualities.

Walls covered with such wallpaper look beautiful. However, you need to remember that you will have to take good care of this wallpaper. They need to be vacuumed (at least once a month). But fabric wallpaper should never be washed! That is why, if stains have already appeared on them, then under no circumstances can they be removed. The only way out is to simply re-glue the entire wall. However, with proper care, fabric wallpaper can last for decades.

Fiberglass wallpaper.

Probably one of the most good views wallpaper In their production, glass fiber threads are used. For this reason, they have special qualities: strength, fire resistance. Dust does not accumulate in them. They also do not cause allergies. They can easily hide wall defects (chips, cracks, etc.).

Painting fiberglass wallpaper

Immediately after gluing, we begin painting the fiberglass wallpaper. They can be repainted 10-12 times (without losing their quality).

Accordingly, they are very often used in service offices or in the process of finishing old buildings. Office landscaping is very important there. Of course, this is not the whole list various types wallpaper There are, for example, wallpaper made from balsa wood fibers or wallpaper made from bamboo...

It's easy to wallpaper at home. So every person can choose wallpaper that he will really like in every sense...