Birdhouse from a 2 liter bottle. Birdhouse from a plastic bottle

Made of wood, but modern parents are ready to make it from any material at hand, for example, plastic bottle. The site "KnowKak.ru" has prepared for you a detailed master class about the simplest birdhouse.

You will need the following materials and tools:

• a plastic bottle of 5 liters. - 1 PC.;
• any twine - 1 skein;
• glue gun, scissors;
• Double-sided tape;
• ribbon and buttons for decoration;
• a piece of woolen fabric;
• needle with thread;
• thick cord;
• marker, stationery knife;
• artificial branches of cereal.

Manufacturing instruction:

Step 1. Cut a strip of double-sided tape and stick it vertically on the bottle, then remove the protective film.

Step 2. Fasten the end of the string at the bottom of the bottle. Stick it on tape.

Wrap twine around the bottle. Try to place each next row tightly to the previous one. This will avoid gaps.

In this way, decorate the entire surface of the flat part of the bottle and its bottom. Be sure to secure the end with glue so that it does not come loose over time.

Step 3. Using a marker, draw a rectangle on one side of the bottle.

Use scissors or a utility knife to cut it out.

This will create a hole through which the birds can fly.

Step 4. Use an old sweater sleeve to insulate the roof. Cut the widest part from it and line up the edges.

Step 5. Put a woolen cloth on top of the bottle, but only up to the level of the twine.

Sew or glue the upper part.

Step 6. Cut artificial or real greens to the required length and glue the woolen threads on top.

Step 7. Decorate the hole with tape and buttons. Stick them on or sew them on.

Step 8. To hang the birdhouse, tie a thick cord around the lid. While doing this, make a loop. Optionally, you can put straw inside the nesting box to keep it warm.

All you have to do is hang the birdhouse on a tree or under the roof. Place some grains inside to attract birds.

With just a 5 liter plastic bottle and twine, you can make a bird house with your children or several pieces at once.

Determining the format

• The birdhouse is a versatile option that suits most birds. Its dimensions are in the range: 40x15x15 cm, and the diameter of the air hole is about 5 cm.
• The titmouse is a haven for sparrows, tits and other small birds. When making it, try to keep within 30x12x10 cm, and make the flight hole no more than 3.5 cm in diameter.
• The wagtail is intended specifically for wagtails. Since these birds mostly walk and not fly, the structure must be placed horizontally, and also provided with a protrusion in front of the hole. The average dimensions of the product are 15x15x30 cm, the taphole is 3 cm.
• The nest often becomes a haven for pikas. Therefore, if in the area suburban area these birds predominate, new house for them, you need to do it in the form of a pyramid with dimensions of 25x25x15 cm, and a through exit, the diameter of which does not exceed 3.6 cm.

In this article, we will talk about birdhouses, since they are versatile and suitable for most birds as a temporary refuge.

Necessary materials

So, if you decide to make a birdhouse from a bottle, we will prepare:

1. 5 liter plastic bottles - 2-3 pieces.
2. Twine.
3. Glue, paints and other materials for decoration.

This set is considered basic. For individual designs, in addition to it, you may need other consumables, which we will mention separately.

Birdhouse from 5 liter plastic bottle

When you collect the above materials, we turn to the question "how to do it." The simplest birdhouse made of a 5 liter plastic bottle is made as follows:

Step # 1. We take plastic container, thoroughly rinse and dry it. We get rid of labels and stuck dirt.

Step # 2. On the side (approximately in the middle) we cut out a round hole and process its edges with a sandpaper or an iron (in the latter case, it must be done through the fabric).

Step # 3. We outline the perch. We make a small hole just below the tap hole and insert a stick of suitable length into it.

Step # 4. We wrap the structure with twine (putting it on glue) or paint it with paint. Note: if you choose twine, winding should be done before cutting the hole.

Step # 5. We draw a tile layout on paper, use a marker to transfer it to the second bottle and cut it out. If one bottle (with a capacity of 5 liters) is not enough, put another one under the knife.

Step 6. To prevent the birdhouse from turning into a birdtrap, we glue the inner walls with burlap or other textured material. It will be easier for birds and their chicks to get out of the house on it.

Step 7. We attach the shingles to the birdhouse with glue or double-sided tape. We wrap the neck of the bottle with twine, which will at the same time serve as a fastener for the new bird house and hide the "tails" of the top layer of the tile.

Step 8. Add other decorative elements as desired. Outside, we cover the entire structure with varnish. Let it dry properly, and our birdhouse is ready.

Now all that remains is to hang it under the windows, and very soon you will be able to enjoy bird chirping in the morning. And also forget about the insects that always terrorize the house adjoining areas.

How to make a birdhouse out of a plastic bottle: useful tips

If you want your plastic bottle birdhouse to perform its functions properly, pay attention to the following points:

• The longer the end of the perch on the outside of the birdhouse, the easier it will be for the cat to get to its feathered inhabitants.
• Decorate only the outer part of the craft, the inner birds will decorate themselves.
• Do you want the life of your feathered wards to be more calm and comfortable? Use mostly discreet colors that merge with the terrain (various shades of brown and green) for decorating the birdhouse, so as not to attract too much attention from predators.
• Do not use to decorate the birdhouse too small elements... During operation, they will quickly fall off, and the structure will lose all its attractiveness.

If you know other live hacks and useful tips, write them in the comments, we will discuss and adopt them.

The benefits of birdhouses

We have said more than once that birds as neighbors bring great benefits to humans. But how exactly is it expressed? For example, in that:

1. The birds destroy harmful insects, caterpillars, larvae, letting them feed their chicks.
2. Most of the birds sing quite beautifully, helping us wake up in good mood and be positive all day.
3. Making a birdhouse is a great chance to upgrade your creative and physical skills, as well as spend time with your family.
4. Building a birdhouse with your own hands teaches children to be productive and take care of nature.

All models of birdhouse from a plastic bottle

Do you want to make a birdhouse from a 5 liter bottle, but ideas and inspiration pass you by? Then we suggest that you familiarize yourself with our photo selection. Below are dozens of ideas, among which there is sure to be one that you will like and will inspire you to new achievements.

More interesting things on our website:

Surely everyone knows about the great benefits that birds bring to the garden. To attract them, a person creates a bird house - a birdhouse. This is often a traditional rectangular design, which is usually made of wood. But you can safely experiment with materials for the house, for example, make a birdhouse out of plastic bottles ... creative birdhouse in addition to being useful, it will also become a spectacular decoration of the garden!

This master class describes in detail the process of making a birdhouse from plastic bottles with your own hands.

To do this, you will need tools and materials such as:

Two 5L plastic bottles. for the house, as well as 2L. for cutting "tiles";
-wooden perch;
-scissors;
-marker;
-glue or double-sided tape;
-brush;
-paints;
- facade acrylic varnish;
-sack for interior decoration birdhouse;
-various decorative elements (small sticks, flowers, butterflies, bells, ladybugs, etc.).

Making a birdhouse begins with cutting out the "tiles" on the roof of the house. The template is applied to the inside of the 2L. bottle, the outline of which is transferred with a marker to the plastic, and then cut out.

Below the entrance, there should be a perch. It is attached very simply, a mark for the cut is drawn on the bottle with a marker, an incision is made along the lines and a perch is inserted.

Through the entrance of the birdhouse, burlap is glued to the inner walls of the house! On the smooth walls of the bottle, the chicks will not be able to get out of the house, so their surface should be rough and textured.

After that, with the help of glue or double-sided tape (not fundamentally), "tiles" are laid over the entire roof area of ​​the birdhouse.

As a result, we got such a wonderful piece!

Then the birdhouse is painted. Birds prefer dark and secluded places, so the house is completely painted over. You can use acrylic paints or even gouache, since after painting the surface of the birdhouse is varnished!

When painting a bird house, creativity and boundless imagination will make the birdhouse very original.

The main thing is to let each layer of paint dry properly!

Gradually, the workpiece takes on a finished look.

The top of the bottle is painted to look like brickwork. And then, in order to hide the end of the last level of the tile, a rope is wound over it.

The "tiled" roof, with the help of different shades, gives a "live" look.

After painting, you can start decorating the birdhouse, the final stage in creating a birdhouse.

With the help of sticks, a fence is created. Sticks are first glued in a bottle, and then tied with a rope until the glue is completely dry.

The resulting fence, if desired, can be painted.

Also, in addition to the fence, the entrance (entrance) of the birdhouse is decorated with branches and an edge is created around the house.

Decorative ladybugs are evenly distributed throughout the house.

The perch is wrapped with a rope, after fixing it on double-sided tape or glue.

The end of the perch is decorated with a bell.

That's all!

A fabulous birdhouse made of plastic bottles is ready!

The final view of the craft. Photo 1.

The final view of the craft. Photo 2.

Now it remains to attach it to one of the trees in the garden and soon a perky bird chirping will be heard from such a house. Realistic lilies of the valley made from plastic bottles will help us to complement the fabulous look of the garden.

Each of us still has school years the arrival of spring is associated not only with warm sunny days, the first young tender greenery, swelling buds, running streams and the singing of birds, by March 8, but also with the manufacture of birdhouses for birds.

It seems only at first glance that making a "house" for starlings is not difficult at all and does not require special skills and knowledge. In fact, making a real, practical and convenient birdhouse is quite difficult, even if you had a basic idea of ​​carpentry.

Paying attention to a birdhouse hanging on a tree, a post or elsewhere, the little one who thinks that it is not enough to simply make and hang it, it turns out that it still requires annual "maintenance". Every year at the beginning of spring, the nesting box should be opened, cleaned and the debris brought on by former guests should be removed so that newly arrived birds can safely build a nest in it and have offspring. Therefore, when making a birdhouse, it is very important to make it collapsible or with at least one opening wall.

In our article, we want to bring to your attention three options for making birdhouses, each of which is accompanied by detailed drawings and an intelligible description, thanks to which you can easily, quickly and simply make your own house for songbirds and look forward to their settling.

1. So, do-it-yourself birdhouse, called "Blue Finch"

The front wall of the birdhouse, measuring 20x170x325 mm, made of coniferous sawn timber - one piece;

The back wall of the birdhouse, measuring 20x170x260 mm, made of softwood lumber - one piece;

Side walls of a birdhouse, measuring 20x175x225 millimeters from coniferous sawn timber - two pieces;

Decorative board of a birdhouse, measuring 20x90x240 millimeters from coniferous sawn timber - one piece;

The bottom of a birdhouse, measuring 20x150x90 mm, made of coniferous sawn timber - one piece;

The roof of the birdhouse, measuring 20x235x190 mm, made of coniferous sawn timber - two pieces;

A perch for a birdhouse, 8 mm in diameter, 75 mm long, made of beech dowel - one piece.

DIY birdhouse - step by step description work.

Step one. To begin with, using the proposed sketches and the indicated dimensions, it is necessary from fiberboard, six millimeters thick, to make templates for the front wall of the birdhouse and two decorative boards, using which you should later transfer, using a simple pencil, the outline of the sketch, one to one, onto a pine board, twenty thick millimeters. Next, you should cut out all the details drawn with a jigsaw, and also drill an inlet hole with a diameter of thirty-two millimeters on the front wall.

Step two. Using the made template of the front wall of the birdhouse, it is necessary to once again transfer the contour of the part to a pine board, twenty millimeters thick, and without making an inlet hole cut out the back part.

Step three. The side walls of the birdhouse must be cut out of a pine board, one hundred and seventy-five millimeters wide. The upper edges of the walls should be beveled at an angle of sixty-seven degrees, and the lower edges at an angle of seventy-eight degrees, after which the length of the side walls, measured from the inside, should be equal to two hundred and twenty-two millimeters.

Step four. Then, from a board, one hundred and fifty millimeters wide, you need to cut out the bottom of the birdhouse, the right and left edges of which should be beveled at an angle of seventy-eight degrees.

Step six. After that, the finished parts of the side walls must be attached to the front of the birdhouse using screws (32 mm) and waterproof glue, so that the edges of the side walls protrude 6 mm beyond the front wall.

Step seven. Then, using the same screws and waterproof glue, you need to attach the bottom of the birdhouse.

Step eight. After that, you should fix the roof to the side and front walls of the birdhouse, without touching the back wall.

Step nine. Previously made decorative planks must be attached to the nesting box using nail polish or waterproof wood glue.

Step ten. Now you need to cut out the board for installing the birdhouse and at a height of ninety-five millimeters from the bottom edge of this board, you need to attach the back wall of the birdhouse.

Step eleven. In the front of the birdhouse, stepping back thirty-two millimeters from the inlet, it is necessary to drill a hole with a diameter of eight millimeters and a depth of twelve millimeters for the perch and glue the manufactured dowel into it, seventy-five millimeters long.

Step twelve. The finished birdhouse on the outer surface should be covered with finishing paint for outdoor use, the inside should be left in its natural form.

2. Simple do-it-yourself birdhouse for small birds.

Required materials for making a birdhouse:

The front wall of the birdhouse, measuring 20x100x290 mm, made of coniferous sawn timber - one piece;

The back wall of the birdhouse, measuring 20x100x245 mm, made of coniferous sawn timber - one piece;

Side walls of a birdhouse, measuring 20x145x235 millimeters from coniferous sawn timber - two pieces;

Decorative board of a birdhouse, measuring 20x50x175 millimeters from coniferous sawn timber - one piece;

The bottom of a birdhouse, measuring 20x100x120 mm, made of coniferous sawn timber - one piece;

The roof of the birdhouse, 20x150x200 mm in size, made of coniferous sawn timber - two pieces;

A board for attaching a birdhouse, measuring 20x75x450 millimeters from coniferous sawn timber - one piece;

Simple do-it-yourself birdhouse- a step-by-step description of the work.

Step one. To begin with, from a pine board, one hundred millimeters wide, it is necessary to cut out the front and back walls of the birdhouse and saw off their upper ends at an angle of 60 degrees, thereby forming a ridge.

Step two. Further, at a distance of two hundred and fifty millimeters from the top, it is necessary to saw off the horizontal lower edge of the rear wall, and cut out a semicircular lower edge on the front wall and, having retreated seventy-five millimeters from the top, drill a hole with a diameter of 032 millimeters.

Step three. Then you should cut out the side walls, as well as the upper edges and bevel them at an angle of sixty degrees.

Step four. The fabricated side walls with screws and waterproof wood glue must be attached to the front wall of the birdhouse.

Step six. After that, from a board two hundred millimeters wide, it is necessary to cut out the roof slopes of the birdhouse and mow each one at an angle of sixty degrees. Additionally, the leading edge of the roof slopes can be shaped.

Step seven. The manufactured roof must be attached to the side and front walls of the birdhouse, without touching the back.

Step eight. Last but not least, you need to cut out the board for attaching the birdhouse measuring 20x75x450 mm, and, together with the back wall, attach it to the birdhouse itself.

Step nine. The finished nesting box should be coated, the outside should be coated with exterior paint, never covering the inside of the nesting box.

3. Roomy do-it-yourself birdhouse for small birds.

Required materials for making a birdhouse:

The front wall of the birdhouse, measuring 20x165x300 millimeters from coniferous sawn timber - one piece;

The back wall of the birdhouse, measuring 20x115x260 mm, made of coniferous sawn timber - one piece;

Side walls of a birdhouse, measuring 20x135x245 millimeters from coniferous sawn timber - two pieces;

Decorative board of a birdhouse, 20x65x175 mm in size from coniferous sawn timber - one piece;

The bottom of the birdhouse, measuring 20x115x135 mm, made of coniferous sawn timber - one piece;

The roof of the birdhouse, measuring 20x175x215 mm, made of coniferous sawn timber - two pieces;

A board for attaching a birdhouse, measuring 20x75x450 millimeters from coniferous sawn timber - one piece;

Spacious do-it-yourself birdhouse for small birds - a step-by-step description of the work.

Step one. To begin with, from a pine board one hundred and sixty-five millimeters wide, it is necessary to cut out the front wall, the upper end of which should be made triangular, with an angle at the top of one hundred and twenty degrees, and the lower end curly.

Step two. Then, in the front wall of the birdhouse, you need to drill an inlet with a diameter of thirty-seven centimeters.

Step three. After that, in the same shape, the back of the birdhouse should be cut out, but with a horizontal lower edge at a distance of two hundred and sixty millimeters from the top of the wall.

Step five. With the help of nails, screws and waterproof wood glue, the front wall of the birdhouse and the two side ones are fastened together, then the bottom, roof, back wall and the birdhouse attachment board are attached.

Step six. Optionally, the birdhouse can be decorated with decorative carved elements.

Step seven. The finished birdhouse, only from the outside, is covered with a special finishing paint for wood for finishing work.

But it turns out birdhouses can be made not only of the traditional sample from wooden planks, easily accessible, waste material - plastic bottles, can also become the basis of a birdhouse for songbirds, and it looks no worse outwardly than.

Birdhouse made of plastic bottles do it yourself.

Required materials for making a birdhouse:

A plastic bottle, with a volume of two to two and a half liters - one piece;

Plastic bottles with a volume of one and a half liters - three to four pieces;

Album sheet of paper;

Simple pencil;

Glue gun;

Scissors;

A round stick, about three to four millimeters in diameter, seven to eight centimeters long;

Do you think you need to run a charitable foundation to help nature?

This is not true!

Everyone can do their bit by building a birdhouse with their own hands.

To do this, you only need instructions and a minimum set of tools. The latter is yours, and the guide is below.

DIY birdhouse: necessary materials

Birdhouses are usually made from planks or plywood. Such birdhouses are more attractive for birds, but it is not always possible to get the right material. Therefore, it is much more convenient to use the means at hand.

It takes one ‒ two plastic bottles and a little imagination to make a cool birdhouse. The amount of material and the list of tools depend on the method of manufacturing the structure.

Specifically, for our example, you will need:

• two plastic bottles - for 2 liters and 5 liters;
• gouache paint;
• glue "Second";
• straight wooden stick;
• acrylic lacquer;
• sackcloth.

Note: the five-liter bottle must be intact, since the birdhouse will be blown out due to the extra holes, which will scare away the birds.

A set of tools for making a birdhouse can be found in any home.

All that is needed is a large scissors, a stationery knife, a marker, and a few brushes for applying paint and varnish.

How to make a do-it-yourself birdhouse from a bottle

After the material is assembled, proceed to manufacture. First, we will make a blank with our own hands, and then we will deal with fine-tuning and decor of the birdhouse.

For convenience, we will divide the process into several stages:

Stage 1. We make the roof.

At this stage, it is necessary to make the "shingles" for the decorative roof. Don't worry, you don't need clay and a kiln. We will cut all the elements from a two-liter bottle.

Cut off the neck and bottom from it. Cut the middle across and unfold. Use a marker to draw the outlines of the "tiles" on the plastic and cut them out with scissors.

Note: To make it the same size, use a cardboard stencil.

Stage 2. The base of the birdhouse.

At the top of the 5-liter container, draw an even circle with a diameter of 4‒5 cm. Next, cut a hole along the outline.

Down from the entrance, at a distance of 2-3 cm, make two intersecting short incisions. In the resulting hole, use glue to secure a wooden stick.

Important! Stick the burlap on the inside of the bottle. This is necessary so that the birds can get out. If you ignore this step, the slippery walls will make the birdhouse not a home, but a death trap.

Stage 3. We lay the "tiles".

To glue the roof elements, start from the bottom edge and gradually work towards the neck of the bottle.

Do not forget that the lower part of the roof must function as a canopy, so do not glue these parts completely.

Stage 4. The final.

For arranging nests, birds prefer shady places, so it is necessary to darken the plastic bottle.

Cover the base with light paint, and the "tiles" - dark. When the gouache is completely dry, treat the birdhouse with acrylic varnish. This is necessary so that the first rain does not wash away the gouache.

The birdhouse is ready, it remains to make it more attractive.

How to decorate a birdhouse

When decorating a birdhouse, try to make it look like a natural object that birds will prefer.

Use wooden sticks, twigs, twine, decorative leaves, insects, etc. for decoration.

Wrap the rope around the perch to make it easier for the birds to sit. Paint the bottle lid under the chimney, and hide the places where the "tiles" adjoin with the same twine.

Make a makeshift fence at the bottom of the birdhouse. To do this, glue sticks around the bottle and tie it with felt. Paint or varnish the decorative hedge if desired.

Line the entrance to the birdhouse with branches in a circle in the shape of a nest. Tie them up with string and secure with glue.

As a result, you will get a cozy home, for which the birds do not even have to take out a mortgage.

To keep birds safe from predators, anchor the birdhouse as high as possible from the ground. The pillars for this are not the best choice so give preference to trees.