I install heating radiators regardless of the location of the old supply pipes.
In addition to the quality of installation, I also pay great attention to the aesthetics of the overall appearance of the connection.
I don't use old pieces of pipe, welded elbows or welded threads... just solid pipe that I bend and thread.
I use a “roller” pipe bender, which guarantees a small radius and a perfectly even pipe bend, regardless of the quality of the pipe being bent.
For packing taps and installing “American” valves, I use anaerobic sealant (guaranteed for the entire service life of the connection without corrosion).
In cases where the installation of taps is done on flax with paste, I roll notches, which guarantees the fixation of the flax and prevents it from being squeezed out.
When welding pipes, I use pipe joining into a socket... based on the requirement
Guaranteed welding without leaking welds the first time. (especially relevant in cases where it is not possible to pressurize the system)
Only high-quality and original materials and time-tested components.
Guarantee of Quality and Aesthetic appearance of all work performed.
and also... Good mood for the entire service life of the heating radiators :)
pipe bending: comparison of bends of a roller pipe bender and a hydraulic one + bends with different bend radii... standard and small, which I use in my work
packaging materials: only high-quality anaerobic Loctite sealants and investment materials... Vibra-Tite paste + Geb flax
knurling of notches: additional guarantee from squeezing out flax when screwing and assembling threaded connections
socket welding: guaranteed high-quality welding joint, regardless of the conditions and ease of welding, recommended by SNiP
High-quality and original materials and components: FAR, RB, GEB, Loctite, Vibro-Tite, Fischer
Replacement of heating radiators with gas welding
Installation, installation of one heating radiator with a turnkey pipe bender - from 10,000 rubles
This amount includes... dismantling the old radiator and all the necessary preparatory and installation work: measurements, threading, crane packing, pipe bending.
As a rule, there is a partial replacement of the riser from the floor to the middle of the riser, above the mounting sleeve, including a complete replacement of horizontal supply pipes. This allows you to achieve horizontal and parallel precision in the location of the supply pipes in relation to the radiator and the wall. As a result, it allows you to place the radiator as expected, regardless of the location (height) of the lower and upper horizontal supply pipes.
Since I use a pipe bender, I only purchase the pipe itself, which I bend myself and cut threads only in the right places for installing taps at the work site... and all this (except for the pipe itself) is already included in the price of installing the radiator!! !
Steel tubular and other non-standard designer radiators Zender, Arbonia, bay window, niches and other non-standard connection types - from 12,000 rubles
Remove the convector (old radiator) and straighten the heating riser - 6,000 rubles
Approximate time to complete gas welding work -
from about 3 days (it all depends on the complexity and number of radiators)First and second day: arrival and preparatory work for assembling new radiators, attaching brackets and hanging radiators (if possible), taking measurements, bending and cutting pipes, cutting threads and packing valves - the most complete preparation before the final stage of pipe welding.
Third day: turning off and draining the water for the final final stage of work - re-welding the supply pipes.
As a rule, the last stage of welding (including adjustment) takes approximately 1.5 - 2 hours for each radiator.
Re-welding of water supply risers with gas welding
Overcooking of one water supply riser in a straight line (galvanization) - from 15,000 rubles .
Approximate time to complete gas welding work - approximately 3 days (depending on complexity)
First and second day: arrival and preparatory work... preparation of riser rods with welding of new bends, bending of pipes to move risers (if necessary) and packing of taps.
Third day: in the first half of the day, shutting off and draining the water for the final, final stage of work... overcooking the risers.
As a rule, to avoid contamination, both water risers (cold and hot) are turned off at the same time... the time it takes to overcook two water supply risers at the same time is approximately 2 hours
Working with frozen pipes
Replacement and installation of one heating radiator with frozen pipes, without disconnecting the heating risers
Time required for freezing pipes- from approximately 3 days (it all depends on the complexity and number of radiators)
It all depends on the complexity of the execution... how many radiators are replaced, so many days of work, taking into account the stages and preparatory work+ installation itself.
As a rule, work occurs in several stages:
1. The most difficult thing... is freezing the riser and dismantling the old convector with a temporary jumper to restore circulation through the heating riser.
2. Assembling a new radiator and hanging it in the right place, followed by taking measurements and preparing the necessary supply pipe blanks.
3. The final stage... re-freezing the riser, with adjustment and final connection of the new heating radiator.
PS. The final price of the work is determined by me only after reviewing the photographs with measurements and understanding the task!
Thermal Imager Inspection
Inspection and identification of heat loss using a Thermal Imager, which allows you to clearly see all defects in the junction of walls and window openings
degree of heating of heating radiators and other cold bridges - 5,000 rubles
PS. in cases of ordering replacement of heating radiators, inspection using a thermal imager... FREE OF CHARGE!!!
Departure, Consultation and Measurements
Visiting the site for inspection, measurements and consultations (at the customer’s request) - 5,000 rubles
PS.Usually, to understand the work, photographs with measurements by mail are enough for me and there is no need for a special visit!!!
This service is for those customers who, for some reason, cannot or do not want to take measurements and it (this service) does not guarantee that I will undertake the fulfillment of your order and in any case it is paid separately, regardless of whether I will fulfill your order or not, since this is primarily a consultation and measurements, according to which in any case I will give you a recommendation and calculation for the selection of radiators, materials and connection diagram.
Transport and other expenses
Purchase and delivery of pipes and components - from 3,000 rubles. (the components and pipes themselves are paid separately)
Also, this amount includes gas refilling (acetylene + oxygen), cleaner + anaerobic sealant, flax with paste and other consumables.
Minimum order:
Due to the technological features of my installation of heating radiators and the need to bring a lot of tools to the site (a whole workshop) + purchase and preparatory work...minimum order from 3 heating radiators or 33,000 rubles
PS. The final price of the work is determined by me only after viewing photos with measurements and understanding the task.
Replacing heating batteries during welding
Today, the service associated with replacing batteries in residential premises is in great demand. This is due to the fact that new options for heating equipment appear on the market, which differ high quality, efficiency and original design.
With the idea of replacing old batteries with new ones, we want to get end result quality work that will be distinguished by quality and reliability. Therefore, you should not save on replacing batteries for welding, even if you really want to save money. It is recommended to immediately entrust the replacement to a specialist who, thanks to his experience, will do everything efficiently, so that the heating system will operate stably and reliably for many years. You can change the batteries in various ways, but the simplest and profitable option This is battery welding. Welding work can be performed using gas or electric welding. The main advantage of replacing batteries by welding is that the end result is a high-quality and reliable connection. In addition, you can also note the cost-effectiveness, since in the near future you will not need to perform maintenance at the junction of the pipe and the battery.
Battery welding - our experience is a guarantee of quality
| 1 | Departure for battery welding | pcs | for free |
| 2 | Material purchase | pcs | for free |
| 3 | Budgeting | pcs | for free |
| 5 | Welding from 20 pcs | pcs | 2500 |
| 6 | Welding batteries from 10 pcs. | pcs. | 3000 |
| 7 | Welding batteries from 4 pcs. | pcs. | 3500 |
| 8 | Welding batteries from 2 pcs | pcs. | 4000 |
| 9 | Welding one battery | pcs. | 5000 |
Welding radiators: what are the advantages?
Due to all the advantages of welding, many consumers prefer this option when replacing batteries. Welding heating batteries has the following advantages:
- Careful appearance, after painting weld remains practically unnoticeable.
- A high degree of reliability, provided that the welding work is carried out by a specialist, the seam is characterized by high strength and durability. It is important to note that the weld can provide the system with much greater reliability than any other modern connection, such as a fitting.
Thanks to the availability of modern welding equipment, the specialists working in our company are able to install batteries in the shortest possible time.
Replacing heating batteries in welding: what you need to know
In order to save a little money, some users try to replace the batteries in their home themselves. However, it should be borne in mind that replacing batteries requires the technician not only to have knowledge and skills, but also to follow certain rules. Violation of the battery installation process can lead to an accident and additional financial costs. Therefore, welding of heating radiators should only be carried out using modern equipment and should only be performed by a qualified specialist. The welding process is as follows. First of all, it is important to find out what the operating pressure is in the heating system; if it exceeds 8 atmospheres, then you should buy bimetallic batteries.
The heating system is completely drained of water, after which the old batteries are cut out with a grinder. The ends of the pipes are thoroughly cleaned of dirt and rust, after which a new battery is installed in the vacant space and welded to the pipes of the heating system using a welding machine.
Our specialists use only high-quality and reliable equipment, which allows for quick dismantling and installation of the battery. Our welding equipment is stable and of high quality, so there are no complications during the battery welding process. Our company’s specialists have extensive experience in carrying out welding work, which allows them to perform work of any complexity with the highest quality and accuracy.
Replacing batteries with gas welding guarantees high-quality seams!
The appearance of new proposals on the heating equipment market prompts the population to think about replacing old batteries with new heating radiators. In order to carry out the replacement, it is important to correctly determine how the heating radiators will be installed. There are many options by which the job can be done, but the most effective is to use a gas welder. This is due to the fact that replacing batteries with gas welding has many advantages such as:
- Increased reliability. Provided that the work is completed by a highly qualified craftsman, the resulting seam will be reliable, thanks to which it can serve ideally for many years. In addition, the weld seam will not require additional attention, as is observed when performing installation using pre-mounted joints. This is due to the fact that the connection point does not have an additional seal, which, as a rule, is not durable in operation.
- Neat appearance. After the welding work is completely completed, the seam remains almost invisible, so it does not spoil the external design of the room and can remain in the open.
Only an experienced technician should be trusted to install heating radiators, since the efficiency and economy of the heating system will depend on the quality of the work performed. Our company’s craftsmen are able to install radiators using gas welding efficiently and accurately.
| 1 | Replacement visit | pcs | for free |
| 2 | Consultation and estimate | pcs | for free |
| 3 | Purchase and delivery of materials | pcs | for free |
| 4 | Replacement of batteries with gas welding from 20 pcs. | pcs | 2500 |
| 5 | Replacement of batteries with gas welding from 10 pcs. | pcs | 3000 |
| 6 | Replacing batteries with a gas welder from 4 pcs | pcs | 3500 |
| 7 | Replacing batteries with a gas welder from 2 pcs | pcs | 4000 |
| 5 | Replacing one battery with gas welding | pcs | 5000 |
The advantage of replacing batteries with gas welding
Welding is a special process in which molten metal is poured between the edges of parts heated to a certain temperature. It is important to note that the edges are heated to a temperature required by the technology and the characteristics of the material itself.
Gas welding work is carried out for welding metal parts of various shapes; in addition, welding is used to eliminate defects from a metal surface, regardless of its shape and size.
Gas welding work to replace batteries consists of:
- preparatory part;
- welding (applying a seam);
- eliminating cracks and cavities from the surface of a metal part;
- smoothing seams (if necessary).
Only specially trained specialists are allowed to perform gas welding work, since only they are able to weld metal surfaces together as correctly and efficiently as possible.
How to replace heating batteries with gas welding
As already noted, with the help of gas welding it is possible to install heating radiators with the highest quality and reliability. The main explanation for this is that the metal edges of the pipe and radiator are connected by molten metal, which is formed as a result of melting the filler wire. Using gas welding, you can easily and most importantly quickly connect steel pipes to a radiator, the outer diameter of which does not exceed 100 millimeters. The fastening points (weld seam) are reliable and able to withstand high operating pressure in the system, which eliminates the possibility of a breakthrough. It should also be noted that the seam made by the master looks very neat compared to fittings and other available
Over time, the owners of their own household or apartment in a multi-storey building have to deal with replacing heating batteries. It is advisable to determine which method to install radiators - using gas welding or the threaded method - together with highly qualified specialists.
Advantages of replacing appliances with gas welding
Without possession special knowledge and the skills to carry out work in this area, it is difficult to decide on the option for installing radiators. It is important to remember that poor-quality installation of heating equipment can result in costly damage to personal and sometimes other people’s property.
In recent years, heating batteries have increasingly been replaced with gas welding. The reason for its great demand is that the resulting weld at the junction of the devices with the riser (pipes) is significantly stronger than the elements being joined together.
This type of connection is able to withstand water hammer and increased pressure of the coolant supplied to the heating system in multi-apartment buildings. The use of gas welding when replacing radiators allows you to avoid leaks and ruptures of joints, as well as wear of the seals used.
Features of the use of gas welding
Externally, a neatly cleaned weld seam looks more aesthetically pleasing than bulky threaded fittings. But it must be taken into account that the installation of heating radiators using gas welding is more suitable for residential buildings with a centralized heat supply system.
In turn, in private households it is necessary to more often carry out work related to removing air from the heating structure and cleaning the radiators. For this reason, in this situation, the use of a threaded connection is preferable to a welded connection, since it makes the process of dismantling/installing devices easier.
Nuances of gas welding work
The connection of several parts during gas welding occurs by heating the joining edges and filler material to the melting temperature. As a result, the resulting connection is highly durable and able to withstand significant loads.
Batteries are replaced by gas welding using special equipment - an acetylene generator, an oxygen cylinder, a burner and a gas reducer. To produce in apartment building gas welding work, you need to obtain the appropriate permit. The welder who must perform this type work, there must be an appropriate certificate and fire safety permit.
Stages of work to replace heating batteries
Everyone has model range Radiators have advantages and disadvantages, depending on the installation location and operating conditions.
Change batteries in stages:
- Preparatory activities. Before replacing batteries on a gas welder, you need to prepare the room, namely, insulate pieces of furniture, cover the floor and walls, protecting them from damage. Liquid is drained from the system. Using an angle grinder, they dismantle devices that have become unusable.
- Assembling a new radiator. At the joints, the nuts are sealed with flax, coated with investment paste and carefully tightened. A valve is placed on top, designed to vent air, and on the side where it joins the pipe, an American valve with a squeegee is installed.
- Installation of a new radiator. It is placed on special brackets, after which all connections with pipes are adjusted - they are welded and then cleaned. You need to know that gas welding is carried out with pipes whose diameter does not exceed 100 millimeters.
- Final stage. After replacing heating radiators using gas welding is completed, you should check the heat supply system for the strength of the connections and their tightness.
The use of gas welding compared to the threaded method is a more expensive and time-consuming process, which has disadvantages. But the advantage of this installation method is its durability and reliability.
The difference between the two replacement options
Replacing batteries using gas welding has a number of advantages over the threaded method:
- welding creates very strong connections;
- the seam is more aesthetically pleasing than the presence of massive fittings and nuts;
- the absence of seals contributes to the durability of joints;
- this is the only way to install radiators in systems with high pressure, since the threads will not withstand such loads;
- When using the threaded method, more than 12 seams are formed, and when using gas welding, no more than 5.
Replacing heating batteries with gas welding (from 4 pcs) 4000 rub
Replacing heating batteries with gas welding (from 2 pcs) 4500
Replacing heating batteries with gas welding (1 piece) 5000 rub.
Estimating 0 rub.
Today, a wide variety of materials are freely available, and on the Internet you can find any instructions and, of course, try to replace heating devices yourself. But can you then be sure of the reliability of the result of your work? After all, it is not enough to select high-quality materials; it is important to thoroughly follow the process technology. Otherwise, you can be left without precious heat at the very inopportune moment– for example, in the midst of winter frosts. So, it is obvious that installing radiators using gas welding is a process that requires an exclusively qualified approach. And, having become more familiar with the technology, you can easily verify this.
Replacing heating batteries with gas welding: the essence of the process
Gas welding at its core is heating the edges of parts of a structure. In some cases, filler material is used in the process. The main advantage of the technology is the absence of the need for a source of electrical energy, as well as the high reliability and tightness of the resulting seams. But in order to achieve this effect, you need to know some features. For example, the power of the heat source must be sufficient to carry out a continuous process, and the temperature must be higher than the oxidation temperature of the metal in the gas.It is equally important to choose the right special equipment for welding work. You will need to purchase a generator (acetylene or some other gas), as well as an oxygen cylinder and gas reducers. And, of course, the welding device itself. It can be a torch or a cutter with a set of replaceable tips. Also in mandatory list The equipment includes: a rubber hose, which is necessary for transferring gas to the tool from cylinders, and a fire-preventing valve.
Replacing heating batteries with gas welding requires that you achieve strong connections, which means that you need to approach the installation of equipment and the choice of welding method as responsibly as possible. You can choose from several existing types of connections, the most popular of which is butt. But if the material used has a thickness of more than 5 mm, then you will already have to choose a Y- or X-shaped edge groove. The most profitable and economical methods of cutting pipes are oxygen, manual and mechanized.
As you already understand, replacing heating radiators with gas welding is a process that requires preliminary study in theory and then consolidation in practice. But few people, of course, want to train on a real object.
If you contact us for help, you will be able to consult on all your questions, as well as receive information on the approximate cost of replacing heating radiators.
The final estimate can be drawn up by a specialist who will conduct a final assessment of the property in person. And then you will only need to prepare the room for the start of work. To do this, it is better to remove excess furniture, cover floor coverings and protect interior details.
Our specialists will do the rest: deliver materials and equipment, agree on draining the central heating risers, and perform pressure testing of the system.
If desired, you can also order the transfer of radiators and risers to a more convenient location, as well as organize the installation of a boiler in a private house for an autonomous heating solution.
Our company is also distinguished by an individual approach to each client. You will be kept informed of each stage of installation, and your wishes will be taken into account when choosing materials for replacing heating batteries with gas welding. Our specialists are ready to answer every question you have, and the final result will be an effective and reliable solution for heating your home.
Loading...
